Skip To Content



Solves the network analysis layer problem based on its network locations and properties.


  • When the solve fails, the warning and error messages provide useful information about the reasons for the failure.

  • Be sure to specify all the parameters on the network analysis layer that are necessary to solve the problem before running this tool.


Solve_na (in_network_analysis_layer, {ignore_invalids}, {terminate_on_solve_error}, {simplification_tolerance}, {overrides})
ParameterExplanationData Type

The network analysis layer on which the analysis will be computed.

Network Analyst Layer
  • SKIPThe solver will skip over network locations that are unlocated and solve the analysis layer from valid network locations only. It will also continue solving if locations are on nontraversable elements or have other errors. This is useful if you know your network locations are not all correct, but you want to solve with the network locations that are valid.
  • HALTDo not solve if there are invalid locations. You can then correct these and rerun the analysis.
  • TERMINATEThe tool will fail to execute when the solver encounters an error. This is the default. When you use this option, the Result object is not created when the tool fails to execute due to a solver error. You should obtain the geoprocessing messages from the ArcPy object.
  • CONTINUEThe tool will not fail and continue execution even when the solver encounters an error. All of the error messages returned by the solver will be converted to warning messages. When you use this option, the Result object is always created and the maxSeverity property of the Result object is set to 1 even when the solver encounters an error. Use the getOutput method of the Result object with an index value of 1 to determine if the solve was successful.

The tolerance that determines the degree of simplification for the output geometry. If a tolerance is specified, it must be greater than zero. You can choose a preferred unit; the default unit is decimal degrees.

Specifying a simplification tolerance tends to reduce the time it takes to render routes or service areas. The drawback, however, is that simplifying geometry removes vertices, which may lessen the spatial accuracy of the output at larger scales.

Because a line with only two vertices cannot be simplified any further, this parameter has no effect on drawing times for single-segment output, such as straight-line routes, OD cost matrix lines, and location-allocation lines.

Linear Unit

Specify additional settings that can influence the behavior of the solver when finding solutions for the network analysis problems.

The value for this parameter needs to be specified in JavaScript Object Notation (JSON). For example, a valid value is of the following form {"overrideSetting1" : "value1", "overrideSetting2" : "value2"}. The override setting name is always enclosed in double quotation marks. The values can be either a number, Boolean, or a string.

The default value for this parameter is no value, which indicates not to override any solver settings.

Overrides are advanced settings that should be used only after careful analysis of the results obtained before and after applying the settings. A list of supported override settings for each solver and their acceptable values can be obtained by contacting Esri Technical Support.


Code sample

Solve example 1 (Python window)

Execute the tool using all the parameters."Route", "HALT", "TERMINATE", "10 Meters")
Solve example 2 (workflow)

The following stand-alone Python script demonstrates how the Solve tool can be used to perform a closest facility analysis and save results to a layer file.

# Name:
# Description: Solve a closest facility analysis to find the closest warehouse
#              from the store locations and save the results to a layer file on
#              disk.
# Requirements: Network Analyst Extension

#Import system modules
import arcpy
from arcpy import env
import os

    #Check out Network Analyst license if available. Fail if the Network Analyst license is not available.
    if arcpy.CheckExtension("network") == "Available":
        raise arcpy.ExecuteError("Network Analyst Extension license is not available.")
    #Set environment settings
    output_dir = "C:/Data"
    #The NA layer's data will be saved to the workspace specified here
    env.workspace = os.path.join(output_dir, "Output.gdb")
    env.overwriteOutput = True

    #Set local variables
    input_gdb = "C:/Data/Paris.gdb"
    network = os.path.join(input_gdb, "Transportation", "ParisMultimodal_ND")
    layer_name = "ClosestWarehouse"
    travel_mode = "Driving Time"
    facilities = os.path.join(input_gdb, "Analysis", "Warehouses")
    incidents = os.path.join(input_gdb, "Analysis", "Stores")
    output_layer_file = os.path.join(output_dir, layer_name + ".lyrx")

    #Create a new closest facility analysis layer.
    result_object =,
                                            layer_name, travel_mode,

    #Get the layer object from the result object. The closest facility layer can
    #now be referenced using the layer object.
    layer_object = result_object.getOutput(0)

    #Get the names of all the sublayers within the closest facility layer.
    sublayer_names =
    #Stores the layer names that we will use later
    facilities_layer_name = sublayer_names["Facilities"]
    incidents_layer_name = sublayer_names["Incidents"]

    #Load the warehouses as Facilities using the default field mappings and
    #search tolerance, facilities_layer_name,
                            facilities, "", "")

    #Load the stores as Incidents. Map the Name property from the NOM field
    #using field mappings
    field_mappings =,
    field_mappings["Name"].mappedFieldName = "NOM", incidents_layer_name, incidents,
                          field_mappings, "")

    #Solve the closest facility layer

    #Save the solved closest facility layer as a layer file on disk

    print("Script completed successfully")

except Exception as e:
    # If an error occurred, print line number and error message
    import traceback, sys
    tb = sys.exc_info()[2]
    print("An error occurred on line %i" % tb.tb_lineno)


Licensing information

  • ArcGIS Desktop Basic: Limited
  • ArcGIS Desktop Standard: Limited
  • ArcGIS Desktop Advanced: Limited

Related topics