PolylineBuilderEx Constructor(MapPoint,Double,Double,Double,ArcOrientation,ClothoidCreateMethod,Double,CurveDensifyMethod,Double,SpatialReference)

In This Topic

Creates a new instance of the PolylineBuilderEx class that is a linear approximation to a clothoid. This method must be called on the MCT. Use QueuedTask.Run.

Syntax

C#
Visual Basic (Declaration)

public PolylineBuilderEx( 
   MapPoint startPoint,
   double startTangentDirection,
   double startRadius,
   double endRadius,
   ArcOrientation orientation,
   ClothoidCreateMethod createMethod,
   double lengthOrAngle,
   CurveDensifyMethod densifyMethod,
   double curveDensity,
   SpatialReference spatialReference
)

Public Function New( _
   ByVal startPoint As MapPoint, _
   ByVal startTangentDirection As Double, _
   ByVal startRadius As Double, _
   ByVal endRadius As Double, _
   ByVal orientation As ArcOrientation, _
   ByVal createMethod As ClothoidCreateMethod, _
   ByVal lengthOrAngle As Double, _
   ByVal densifyMethod As CurveDensifyMethod, _
   ByVal curveDensity As Double, _
   Optional ByVal spatialReference As SpatialReference _
)

Parameters

startPoint: The start point of the polyline.
startTangentDirection: The tangent direction of the spiral, north azimuth, at the first point of the spiral. The unit of the azimuth is radians.
startRadius: The radius at the start of the spiral. The radius must be greater than zero. Double.Infinity is a valid value for the radius.
endRadius: The radius at the end of the spiral. The radius must be greater than zero. Double.Infinity is a valid value for the radius.
orientation: The orientation of the spiral.
createMethod: The method of creation. ClothoidCreateMethod.ByLength signifies that lengthOrAngle specifies the length of the entire spiral. ClothoidCreateMethod.ByAngle signifies that lengthOrAngle specifies the angle, in radians, measuring the span of the arc from the start to the end of the clothoid path.
lengthOrAngle: Either the length of the clothoid or the central angle of the clothoid as specified by createMethod.
densifyMethod: The method of densification.
curveDensity: If densifyMethod is CurveDensifyMethod.ByLength, then curveDensity is the maximum segment length allowed in the clothoid. If densifyMethod is CurveDensifyMethod.ByDeviation, then curveDensity is the maximum distance, in meters, that the clothoid can deviate from the actual curve. If densifyMethod is CurveDensifyMethod.ByAngle, then curveDensity is the maximum angle between tangent lines to the curve.
spatialReference: (Optional) The spatial reference of the polyline. The default value is null.

Exceptions

Exception	Description
System.NotImplementedException	This method or property must be called within the lambda passed to QueuedTask.Run.

Remarks

A clothoid, also known as an Euler spiral, is a curve such that its curvature is equal to a constant times its length. Curvature is a value that measures how curved or flat the curve is at a point. The larger the curvature, the more flat the curve is. The curvature is equal to the reciprocal of the radius. If the radius is infinity, then the curvature is zero. i.e. flat.

Shown below is a clothoid with startTangentDirection = 0, startRadius = double.PositiveInfinity, endRadius = 1, orientation = ArcOrientation.ArcCounterClockwise, createMethod = ClothoidCreateMethod.ByLength, and lengthOrAngle = 10.

Here is a clothoid with startTangentDirection = Math.PI / 4, startRadius = double.PositiveInfinity, endRadius = 0.8, orientation = ArcOrientation.ArcClockwise, createMethod = ClothoidCreateMethod.ByLength, and lengthOrAngle = 10.

Now here is a clothoid such that the start radius is smaller than the end radius. It has startTangentDirection = Math.PI / 3, startRadius = 2, endRadius = 10, orientation = ArcOrientation.ArcClockwise, createMethod = ClothoidCreateMethod.ByLength, and lengthOrAngle = 20.

Example

Construct a Clothoid by Length

MapPoint startPoint = MapPointBuilderEx.CreateMapPoint(0, 0);
MapPoint queryPoint = MapPointBuilderEx.CreateMapPoint(3.8, 1);
double tangentDirection = 0;
ArcOrientation orientation = ArcOrientation.ArcCounterClockwise;
double startRadius = double.PositiveInfinity;
double endRadius = 1;
ClothoidCreateMethod createMethod = ClothoidCreateMethod.ByLength;
double curveLength = 10;
MapPoint pointOnPath;
double radiusCalculated, tangentDirectionCalculated, lengthCalculated, angleCalculated;


PolylineBuilderEx.QueryClothoidParameters(queryPoint, startPoint, tangentDirection, startRadius, endRadius, orientation, createMethod, curveLength, out pointOnPath, out radiusCalculated, out tangentDirectionCalculated, out lengthCalculated, out angleCalculated, SpatialReferences.WGS84);

pointOnPath = MapPointBuilderEx.CreateMapPoint(3.7652656620171379, 1.0332006103128575);
radiusCalculated = 2.4876382887687227;
tangentDirectionCalculated = 0.80797056423543978;
lengthCalculated = 4.0198770235802987;
angleCalculated = 0.80797056423544011;

queryPoint = MapPointBuilderEx.CreateMapPoint(1.85, 2.6);

PolylineBuilderEx.QueryClothoidParameters(queryPoint, startPoint, tangentDirection, startRadius, endRadius, orientation, createMethod, curveLength, out pointOnPath, out radiusCalculated, out tangentDirectionCalculated, out lengthCalculated, out angleCalculated, SpatialReferences.WGS84);

pointOnPath = MapPointBuilderEx.CreateMapPoint(1.8409964973501549, 2.6115979967308132);
radiusCalculated = 1;
tangentDirectionCalculated = -1.2831853071795867;
lengthCalculated = 10;
angleCalculated = 5;
 
tangentDirection = Math.PI / 4;
orientation = ArcOrientation.ArcClockwise;
startRadius = double.PositiveInfinity;
endRadius = 0.8;
createMethod = ClothoidCreateMethod.ByLength;
curveLength = 10;

Polyline polyline = PolylineBuilderEx.CreatePolyline(startPoint, tangentDirection, startRadius, endRadius, orientation, createMethod, curveLength, CurveDensifyMethod.ByLength, 0.5, SpatialReferences.WGS84);

Requirements

Target Platforms: Windows 11, Windows 10

ArcGIS Pro version: 3 or higher.

Reference

PolylineBuilderEx Class
PolylineBuilderEx Members
Overload List

Send feedback