Add a point event by route and measure

Available with Location Referencing license.

Characteristics of a route can be represented as point events with measure information along the route. Use the Add Point Event tool to create single point events in ArcGIS Pro.

The example in the following workflow demonstrates adding a point event at measure 5 on Route1 using the Add Point Event tool Add a single point event.

The following diagram shows the route attributes. The route (Route1) has measures from 0 to 20.

Before adding a point event to a route using the Add Point Event tool

The following table details the route attributes:

Route IDFrom DateTo Date

Route1

1/1/2000

<Null>

Add a point event

Complete the following steps to add a point event by route and measure:

  1. Open the map in ArcGIS Pro and zoom in to the location where you want to add the point event.
  2. On the Location Referencing tab, in the Events group, click Add > Point Event Add a single point event.

    The Add Point Event pane appears.

    Add Point Event pane

    Using the Route and Measure method, the measure location is based on the measure values from the selected route.

  3. Click Next.

    The Route and Measure fields appear in the Add Point Event pane.

    Add Point Event pane
  4. Click the Event Layer drop-down arrow and choose the point event layer where you want to add the event.

    The selected Network value is based on the selected event layer.

  5. Specify a route by doing either of the following:
    • Provide a route name in the Route ID text box.
    • Click Choose route from map Choose route from map, and click on the route where you want to add the point event.

    The measure is initially populated using the route location where you clicked.

    Tip:

    After clicking Choose route from map Choose route from map or Choose measure from map Choose measure from map, hover over the route to see the route and measure at the location of the pointer.

    You can choose a scale for the display of route and measures.

    Note:

    If a message regarding acquiring locks or reconciling appears, conflict prevention is enabled.

  6. Specify a new location by doing one of the following:
    • Provide the value in the Measure text box.
    • Click Choose measure from map Choose measure from map and click the measure value along the route on the map.

    Once the measure is provided, a green dot appears on the map at that measure location.

  7. The start date default value is today's date, but you can change the date by doing one of the following:
    • Provide the start date in the Start Date text box.
    • Click Calendar Calendar and choose the start date.
    • Check the Route start date check box.
  8. Optionally, specify the end date for the point event by doing one of the following:
    • Type the end date in the End Date text box.
    • Click Calendar Calendar and choose the end date.
    • Check the Route end date check box.

    If no end date is provided, the event remains valid from the event start date into the future.

  9. Click Next.

    The attributes for the chosen point event layer appear under Manage Attributes.

    Manage Attributes table
  10. Provide attribute values for the event layer.
    Note:

    Click Copy attribute values by selecting event on the map Copy attribute values by selecting event on the map and click an existing point event belonging to the same event layer on the map to copy event attributes from that event.

  11. Click Run.

    A confirmation message appears once the new point event is added and appears on the map.

The following table provides details about the point event:

EventRoute IDFrom DateTo DateMeasureLocation ErrorOwner

Event1

Route1

1/1/2000

<Null>

5

No Error

County

The following diagram shows the route and the associated event after the edit:

Route1 with a point event

Referent offset when using the route and measure method

The Roads and Highways events data model supports the configuration of referent event fields and their enablement using the Enable Referent Fields tool. Once referent fields are configured and enabled in a layer, referent locations are populated and persisted in that layer when events are added or edited.

When a point event is created using route and measure in a referent-enabled layer, the parent LRS Network is used as the RefMethod value by default. The route ID is used as the RefLocation value, and the measure of the new point event is used as its RefOffset value.

If the measure of a point event is updated, the RefOffset value updates to reflect the measure value.

The examples below demonstrate the impact of adding a point event record to an event layer that has referent values enabled.

Before adding a point event with referents

The following diagram shows the route:

Before event creation with referents

The following table provides details about the route.

Route IDFrom DateTo Date

Route1

1/1/2000

<Null>

After adding a point event with referents

In the following diagram, a point event that has referents has been added at measure 5:

After event creation with referents

The following table provides details about the event referent fields after event creation:

Event IDRefMethodRefLocationRefOffset

Event1

AllRoutes

Route1

5

The following table provides details about the event record after adding a point event at measure 5. The parent LRS Network is used as the RefMethod value, and the route is used as the RefLocation value:

Event IDRoute IDFrom DateTo DateMeasureRefOffset

Event1

Route1

1/1/2000

<Null>

5

5

You can edit the event using the attribute table so that it uses referents other than the default. If subsequent route edits are made, the RefMethod and RefLocation values revert to the parent LRS Network and the route, respectively.