Apply cartographic realignment

Available with Location Referencing license.

You can update route geometry based on aerial imagery, as-built drawings, or input from field data collectors without changing measures by making direct modifications to the centerline. This is known as cartographic realignment. ArcGIS Roads and Highways allows you to change the shape of centerlines and preserve the calibration of underlying routes as they existed before cartographic realignment.

Note:

The centerline feature class must be visible in the Contents pane to apply cartographic realignment.

Tip:

Cartographic realignment uses the LRS Network's Update route measures in cartographic realignment property. This property is disabled by default. It can be enabled for routes in the LRS Network using the Update route measures in cartographic realignment parameter of the Modify Network Calibration Rules tool.

When Update route measures in cartographic realignment is enabled in a network in which cartographic realignment is performed, route measures can change after cartographic realignment. Subsequently, changes to route measures after cartographic realignment can impact events associated to the route depending on the configured event behavior.

Learn more about updating route measures and events in cartographic realignment

  1. Add the centerline and network feature class to a map.

    Alternatively, open a map in which the centerline and network feature class are present.

    Note:

    The information model expects only one centerline at any given location. Ensure that the centerlines you're using for your edit do not overlap other centerlines in the LRS.

    Note:

    Traditionally versioned networks must be edited through a direct connection to the geodatabase. Branch versioned networks, including networks configured with a user-generated route ID, must be edited through a feature service.

  2. Zoom in to the location of the route that you want to realign.

    Note:

    The centerline feature for cartographic realignment of the route must exist in the centerline feature class prior to the realignment.

    Locating the route to be realigned

  3. Uncheck the network layer in the Contents pane, on the List By Selection tab List By Selection, in the Selection list.
  4. Check the centerline layer in the Contents pane, on the List By Selection tab List By Selection, in the Selection list.
  5. Select the centerline feature for the edit in the map.
  6. Double-click the centerline's edge.

    The selected centerline's vertices appear.

    Editing vertices and segments
  7. Edit the centerline's vertices as necessary.

    You can edit feature vertices and modify centerline segments using Modify Features tools . You can also use the geometry editing tools available in Roads and Highways.

    Moving vertices and segments
  8. After editing the vertices to match the proposed alignment of the route, right-click anywhere on the map and click Finish.

    The route is cartographically realigned.

    Cartographically realigned route
    Note:
    • After centerlines are updated, the route shapes in all networks are also updated. However, the event shapes for events and locations of the managed intersections are not updated until you run the Apply Event Behaviors and Generate Intersections geoprocessing tools.

      Learn more about scenarios for generating and updating intersections

    • It is also important to note that when the centerlines are edited, all routes in all networks, across all times, are modified accordingly.
    • If conflict prevention is enabled, locks are acquired on all routes associated with the centerline being edited.
    Note:

    If a message regarding acquiring locks or reconciling appears, conflict prevention is enabled.

Complex route cartographic realignment scenarios

Scenarios for complex route cartographic realignment on loop and lollipop routes when Update route measures in cartographic realignment is disabled are described below.

Cartographic realignment on a loop

In the following example, an undershoot is fixed on a loop route that has a start measure of 0 and an end measure of 4 before cartographic realignment:

Input for cartographic realignment of an undershoot on a loop route

After cartographic realignment, the undershoot on the loop is fixed and two intermediate calibration points are added at measures 1.33 and 2.67.

Output for cartographic realignment of an undershoot on a loop route
Note:

If the Update route measures in cartographic realignment property is disabled, then existing intermediate calibration points will have updated measures to account for the shape change. If this property is enabled, only calibration points upstream of the cartographic realignment will have their measures changed.

This means, in the example above, the location of the intermediate calibration points stays the same, but their measures can change.

Cartographic realignment on a lollipop

In the following example, an undershoot is fixed on a lollipop route that has a start measure of 0 and an end measure of 5 before cartographic realignment:

Input for cartographic realignment of an undershoot on a loop route

After cartographic realignment when Update route measures in cartographic realignment is disabled, the undershoot on the lollipop is fixed and two intermediate calibration points are added at measures 2.46 and 3.86.

Output for cartographic realignment of an undershoot on a loop route

In the following example, an overshoot is fixed on a lollipop route that has a start measure of 0 and an end measure of 5 before cartographic realignment:

Input for cartographic realignment of an undershoot on a loop route

After cartographic realignment when Update route measures in cartographic realignment is disabled, the overshoot on the lollipop is fixed.

Output for cartographic realignment of an undershoot on a loop route