View LRS event properties—ArcGIS Pro

Location Referencing ライセンスで利用可能です。

You can view the properties of an LRS event as either a map layer or a feature class.

To modify existing LRS event properties, use the Modify LRS Event geoprocessing tool.

LRS event properties

The following tables describe the LRS event properties:

Event name and event feature class properties appear at the top of the Location Referencing tab.


Property	Description
Event Name	The name of the selected event.
Event Feature Class	The feature class from which the LRS event was created.
Event Type	The data type of the selected event: linear or point.
Parent Network	The LRS Network in which the event is located.

You can view the following Tolerance and Resolution properties:


Property	Description
Measure Precision	The specified number of decimal places included in the measure.
XY Tolerance	The x,y tolerance set for the network feature class.
M Tolerance	The m-tolerance set for the network feature class.
Z Tolerance	The z-tolerance set for the network feature class.
XY Resolution	The x,y resolution set for the network feature class.
M Resolution	The m-resolution set for the network feature class.
Z Resolution	The z-resolution set for the events feature class.

You can view the following Event Fields properties for the events feature class:


Property	Description
Event Id	The unique ID for each event record.
From Route Name	The name of route from which the From measure is derived.
From Route Id	The unique ID of the route from which the From measure is derived.
From Measure	The measure on the route where the beginning of the event will be located.
To Route Name	The name of route from which the To measure is derived.
To Route Id	The unique ID of the route from which the To measure is derived.
To Measure	The measure on the route where the end of the event is located.
From Date	The date the event became active on the route.
To Date	The date the event was retired on the route.
Location Error	The location error for the event.
Supports Spanning Routes	Indicates whether the event was registered with span routes enabled.

You can view the following Referent Fields properties:


Property	Description
From Referent Method (linear events)	Method of referencing the offset feature. This can be x,y coordinates, stationing, length, LRS Network, event, intersection, or other point feature classes.
From Referent Location (linear events)	Location of the offsetting feature. This can be an x,y coordinate, feature or event ID, or intersection ID.
From Referent Offset (linear events)	The offset measure. Saved in the unit of measure configured when configuring offset fields.
To Referent Method (linear events)	Method of referencing the offset feature. This can be x,y coordinates, stationing, length, LRS Network, event, intersection, or other point feature classes.
To Referent Location (linear events)	Method of referencing the offset feature. This can be x,y coordinates, stationing, length, LRS Network, event, intersection, or other point feature classes.
To Referent Offset (linear events)	The offset measure. Saved in the unit of measure configured when configuring offset fields.
Offset Units	The unit of measure for offsets in the LRS Network in which the event resides.

You can view the following Event Behavior Rules configured for the selected LRS Network.

The event behavior rules are configured and applied to each of the activity types (calibrate, retire, extend, reassign, and realign) using the Apply Event Behaviors geoprocessing tool.

You can view the properties of an LRS event map layer from the Contents pane:

Open the Contents pane in ArcGIS Pro.
Right-click the event layer whose properties you want to view and click Properties.
The Layer Properties dialog box appears with the selected network layer name shown in the title bar.
注意:
The dialog box tabs that appear on the left of the dialog box are specific to the selected layer type.
Click the Location Referencing tab on the left.
Scroll down if the tab isn't visible in the list.
The Location Referencing tab displays general properties for your selection at the top, with additional nodes below.
Click the arrow for a node to expand or collapse its properties.
If the value or field name is longer than the display, hover over the property to view its details, or resize the dialog box to view additional details.
ヒント:
You can copy the read-only properties to your clipboard.
Click OK to exit the Layer Properties dialog box.

You can view the properties of an LRS event feature class from the Catalog pane:

Open the Catalog pane in ArcGIS Pro.
Expand the geodatabase connection and any subfolders to browse to the feature class.
Right-click the event feature class whose properties you want to view and click Properties.
The Feature Class Properties dialog box appears with the selected feature class name shown in the title bar.
注意:
The dialog box tabs that appear on the dialog box are specific to the selected layer type.
Click the Location Referencing tab on the left.
Scroll down if the tab isn't visible in the list.
The Location Referencing tab displays general properties for your selection at the top, with additional nodes below.
Click the arrow for a node to expand or collapse its properties.
If the value or field name is longer than the display, hover over the property to view its details, or resize the dialog box to view additional details.
ヒント:
You can copy the read-only properties to your clipboard.
Click OK to exit the Feature Class Properties dialog box.