Smart Tree layout reference

Smart Tree is a tree layout algorithm that applies to any type of diagram.

This layout algorithm arranges the diagram features hierarchically and places them in a smart tree according to the direction and spacing distances specified.

Root flags can be set up on diagram junctions before executing the Smart Tree layout.

When a root junction is specified in the diagram, the Smart Tree layout algorithm builds a smart tree starting from that junction.

When several root junctions are specified in the diagram, those root junctions are aligned along the same axis perpendicularly to the tree direction and appear as different start points for a tree branch of the diagram.

If no root junction is specified, the algorithm identifies the diagram junction associated with the smallest network topology index and uses this junction as the root junction.

The examples below show a diagram before and after applying the Smart Tree layout, respectively:

Before and after applying the Smart Tree layout

Apply the Smart Tree layout on an active diagram map view

When applying this layout on a network diagram, the following prerequisites must be met:

  • Since this operation is transactional, edits must be saved before it is run.
  • The input network diagram layer to which the layout applies must be from either a utility network or trace network in a file or mobile geodatabase, or a network diagram service. When working with a utility network or a trace network in an enterprise geodatabase, the input network diagram layer must be from a service

To apply the Smart Tree layout on an active diagram map view, do one of the following:

  • On the Network Diagram tab, click the drop-down arrow on the Diagram Layouts button in the Layout group, and depending on the tree direction you want, click one of the Smart Tree layout items in the gallery—Smart Tree Layout - Left to Right, Smart Tree - From Right to Left Layout, Smart Tree - From Bottom to Top Layout, Smart Tree - From Top to Bottom Layout.
  • Load the Apply Smart Tree Layout tool in the Geoprocessing pane, adjust the Smart Tree layout parameters and click Run

Note:

To apply the layout on a subset of features in the network diagram, use one of the Select Features tools (for example, Select By Rectangle, Select By Polygon, and so on) and select the diagram features before running.

Configure the Smart Tree layout on a diagram template

To configure this layout on your diagram template, use the Add Smart Tree Layout tool.

Smart Tree layout parameters

The sections below clarify the main Smart Tree diagram layout parameters:

Apply Smart Tree Layout parameters

Preserve container layout

Most of the layout algorithms work with the Preserve container layout option. This option allows controlling the algorithm execution so it executes either on the top graph of the diagramPreserve container layout checked, or on both content and noncontent features in the diagram—Preserve container layout unchecked.

Learn more about the Preserve container layout option

Tree Direction

This parameter sets the direction of the tree:

Smart Tree layout—Tree Direction

Spacing values interpreted as absolute units in the diagram coordinate system

Some layout algorithms work with the Spacing values interpreted as absolute units in the diagram coordinate system option. This option specifies how the layout algorithm parameters representing distances will be interpreted:

  • Checked—The layout algorithm will interpret any distance values as linear units.
  • Unchecked—The layout algorithm will interpret any distance values as relative units to an estimation of the average of the junction sizes in the current diagram extent. This is the default.

Between Subtrees

This parameter is used to specify the spacing between two neighboring subtrees, that is, the spacing between diagram junctions that are displayed perpendicular to the smart tree direction and belong to a different subtree, such as the A spacing below:

Smart Tree layout—Between Subtrees

Between Junctions Perpendicular to the Direction

This parameter is used to set the spacing between diagram junctions that are displayed perpendicular to the smart tree direction and belong to the same subtree level, that is, the B spacing below:

Smart Tree layout—Between Junctions Perpendicular to the Direction

Between Junctions Along the Direction

This parameter value specifies the spacing between diagram junctions that are displayed along the smart tree direction, that is, the C spacing below:

Smart Tree layout—Between Junctions Along the Direction

Between Disjoined Graphs

This parameter is used to specify the minimum spacing that must separate features belonging to disjoined graphs when the diagram contains such graphs, that is, the D spacing below:

Smart Tree layout—Between Disjoined Graphs

Edge Display Type, Break Point Relative Position, and Offset

These parameters are related. The Break Point Relative Position and Offset parameters are used depending on the specified Edge Display Type parameter value.

Edge Display Type

The Edge Display Type parameter specifies how diagram edges that are related to the tree branches display. There are three types of tree branch geometry:

  • Curved edges—All diagram edges related to the tree branches are curved.
  • Regular edges—All diagram edges related to the tree branches do not display with right angles.
  • Orthogonal edges—All diagram edges related to the tree branches display with right angles.
Tree layout—Edge Display Type

Break Point Relative Position

The Break Point Relative Position parameter specifies the relative position of the break point that will be inserted along the diagram edges when Edge Display Type is Regular edges or Orthogonal edges. It is a percentage between 0 and 100.

  • With a Break Point Relative Position (%) value of 0, the break point is positioned at the x-coordinate of the edge's from junction and at the y-coordinate of the edge's to junction for a horizontal tree. It is positioned at the y-coordinate of the edge's from junction and at the x-coordinate of the edge's to junction for a vertical tree.
  • With a Break Point Relative Position (%) value of 100, there is no break point inserted on the diagram edges; each diagram edge directly connects its from and to junctions.
  • With a Break Point Relative Position (%) value of N between 0 and 100, the break point is positioned at N% of the length of the [XY] segment, X being the x-coordinate of the edge's from junction and Y being the y-coordinate of the edge's to junction for a horizontal tree. It is positioned at N% of the length of the [YX] segment, Y being the y-coordinate of the edge's from junction and X being the x-coordinate of the edge's to junction for a vertical tree.
Break point relative position samples when using Orthogonal edges or Regular edges

When Edge Display Type is Curved edges, the Break Point Relative Position parameter is used to compute the relative position of the two inflection points that will be inserted along the diagram edges to compute the curved edges geometry. It is a percentage between 15 and 40. With a Break Point Relative Position (%) value of N between 15 and 40, the following is true:

  • X being the x-coordinate of the edge's from junction and Y being the y-coordinate of the edge's to junction for a horizontal tree:
    • The first inflection point will be positioned at N% of the length of the [XY] segment.
    • The second inflection point will be positioned at (100 - N)% of the length of the [XY] segment.
  • Y being the y-coordinate of the edge's from junction and X being the x-coordinate of the edge's to junction for a vertical tree:
    • The first inflection point will be positioned at N% of the length of the [YX] segment.
    • The second inflection point will be positioned at (100 - N)% of the length of the [XY] segment.
The examples below show these inflection points when Edge Display Type is Curved edges, depending on different Break Point Relative Position parameter values:
Break point relative position examples when using Curved edges

Offset

When Edge Display Type is Orthogonal edges, the Offset parameter specifies the offset used to separate overlapping segments. It is a double value that cannot exceed 10 percent of the smallest value specified for the other spacing parameters.

Offset sample when using Orthogonal edges

Related topics