Realign routes

Location Referencing ライセンスで利用可能です。

During the life span of a roadway, route geometry and length can change. Route sections are updated while others are added. Major changes, such as environmental concerns or repair work, can require an update in the shape of the route's geometry and length.

ArcGIS Roads and Highways uses centerlines to do realignment. The Realign Route tool can be used to realign a single route or to realign several adjoining routes that are part of the same line.

Centerline features used to realign routes can be existing features in the centerline feature class, be digitized into the centerline feature class (using aerial photography or other basemaps for guidance), be copied and pasted from other feature classes, or be imported from CAD files or other ArcGIS-supported data sources.

This table explains the parameters used in the Realign Route tool.

VariableContinuous Measure network

Network

The network in which the continuous routes exist.

Effective Date

The date when the realignment has taken place on the ground.

Source Route: Route ID

The route where the realignment takes place.

Source Route: From measure

The measure on the source route where the realignment starts; shown by the green dot.

Source Route: To measure

The measure on the source route where the realignment ends; shown by the red dot.

Realigned Route: From measure

The starting measure on the realigned portion.

Realigned Route: To measure

The ending measure on the realigned portion.

Route realignment scenario

In the following example, the route (RouteXYZ) has a start measure of 0 and an end measure of 30 before realignment. The realign section has measures from 10 to 20.

Example 1: Before realign

Route IDRouteXYZ

From Measure

10

To Measure

20

Recalibrate downstream

Yes

After realignment, the realigned section has measures from 10 to 35, while the entire route has measures from 0 to 45.

Example 1: After realign

Route IDRouteXYZ

From Measure

10

To Measure

35

Complex route realignment scenarios

The following sections provide examples of realignment in complex routes, including loop, lollipop, gapped, branch, and infinity routes:

Realign a loop route

The route is realigned from measure 0 to measure 4, which is from the beginning to the middle of the route. In the following example, a route (RouteX) has a start measure of 0 and an end measure of 12 before realignment:

Example 1: Input for realign on a loop route

With downstream recalibration, the realignment results in a RouteX start measure of 0 and end measure of 17. 5.

Example 1: Output for realign on a loop route

Realign a lollipop route

The route (RouteX) is realigned from measure 8 to measure 15. In the following example, the route has a start measure of 0 and an end measure of 15 before realignment:

Example 1: Input for realign on a lollipop route

As the realignment is from the middle to the end, downstream recalibration does not apply. RouteX is realigned with a start measure of 0 and an end measure of 17.

Example 1: Output for realign on a lollipop route

Realign a gapped route

In the following example, a gapped route (RouteX) has a start measure of 0 and an end measure of 4 before realignment. The route is realigned from measure 1 to measure 3, which is in the middle of the route.

Example 1: Input for realign on a gapped route

With downstream recalibration, the realignment will result in a RouteX start measure of 0 and an end measure of 12.

Example 1: Output for realign on a gapped route

Realign an infinity route

In the following example, a route (RouteX) has a start measure of 0 and an end measure of 24 before realignment. The route is realigned from measure 7 to measure 11, which is in the middle of the route.

Example 1: Input for realign on an infinite route

With downstream recalibration, RouteX has a start measure of 0 and an end measure of 26.

Example 1: Output for realign on an infinite route

Realign a branch route

In the following example, a route (RouteX) that has a start measure of 0 and an end measure of 9 before realignment is realigned in the middle:

Example 1: Input for realign on a branch route

With downstream recalibration, the realigned RouteX has a start measure 0 and an end measure of 12.

Example 1: Output for realign on a branch route

Use the following steps to realign routes:

注意:

ルートを編集する際は、ギャップ キャリブレーション ルールが適用されます。

  1. 中心線フィーチャクラスとネットワーク フィーチャクラスをマップに追加します。

    中心線フィーチャクラスとネットワーク フィーチャクラスがすでに存在するマップを開くこともできます。

    注意:

    情報モデルでは、特定場所で 1 つの中心線のみが必要です。 編集に使用している中心線が LRS で他の中心線と重なり合っていないことを確認します。

    注意:

    トラディショナル バージョン対応ネットワークは、ジオデータベースへの直接接続を介して編集する必要があります。 ブランチ バージョン対応ネットワーク (ユーザー生成ルート ID を使用して構成されたネットワークを含む) は、フィーチャ サービスを通じて編集する必要があります。

  2. Zoom in to the location where you want to realign the route.

    注意:

    The centerline feature for realigning the route must exist in the centerline feature class before realigning the route.

  3. On the Location Referencing tab, in the Routes group, click Realign 再配置.
    Realign button

    The Realign Route pane appears with the Select By Rectangle option 四角形による選択 as the default.

  4. Use your mouse to select one or more centerlines by rectangle at the location of the new route.

    You can also click the Select one or more centerlines drop-down arrow to choose one of the remaining selection tools: Select By Polygon Select by Polygon, Select By Lasso Select by Lasso, Select By Circle Select by Circle, Select By Line Select by Line, or Select By Trace トレースによる選択.

    Alternatively, you can use the interactive selection tools on the Map tab on the ArcGIS Pro ribbon:

    The selected centerlines are highlighted on the map and the Allow choosing of one or more centerlines button 1 つ以上の中心線の選択を許可 appears in the Realign Route pane. The Selected Centerlines count is shown above the table.

    注意:
    • The direction of digitization of the centerline, depicted by the direction of the arrowhead on the selected centerline, also determines the direction of increasing measure calibration. You can reverse direction for the chosen centerlines using the Flip the direction of the centerlines button 中心線の方向を反転.
    • You can keep the centerlines chosen after realigning the route.
  5. Click the Allow choosing of one or more centerlines button 1 つ以上の中心線の選択を許可.

    A table appears in the Realign Route pane with each chosen centerline in a numbered row that corresponds to the selection order. Chosen centerlines are numbered on the map and highlighted. The Chosen Centerlines count is shown below the table.

    Realign Route pane
  6. Optionally, change the centerline selection order by choosing one or more rows from the Order column and using the buttons below the table. You can also drag rows into the desired order.

    Changes in the table selection order are also shown on the map.

    Tools available in the centerlines table

    ToolTool nameTool description
    1 つ以上の中心線の選択を許可

    Allow choosing one or more centerlines

    Allows you to choose the centerlines on the map and displays them in a table by order of selection. Use the move buttons below the table or drag rows to reorder the chosen centerlines.

    現在選択されている中心線を消去

    Clear the currently chosen centerlines

    Clears the chosen centerlines and keeps the selected centerlines. You can reselect after clicking this button or click the Allow choosing one or more centerlines button a second time.

    選択した中心線を上に移動

    Move chosen centerlines up

    Moves one or more selected centerlines up a row in the table order.

    選択した中心線を最上位へ移動

    Move chosen centerlines to the top

    Moves one or more centerlines to the top of the table order.

    選択した中心線を下に移動

    Move chosen centerlines down

    Moves one or more centerlines down a row in the table order.

    選択した中心線を最下位へ移動

    Move chosen centerlines to the bottom

    Moves one or more centerlines to the bottom of the table order.

    中心線の方向を反転

    Flip the direction of the centerlines

    Reverses the direction of the chosen centerlines.

    選択した中心線を削除

    Remove the chosen centerlines

    Removes the chosen centerline from the table order but leaves it selected.

    ヒント:

    To change the display field shown in the centerlines table, right-click the centerline feature class in the Contents pane and choose Properties from the context menu. On the Layer Properties dialog box, click the Display tab, and click the Display field drop-down arrow to change its value. In the previous image, the display field is OBJECTID.

  7. In the Realign Route pane, choose the network in which you want to realign a route.
    注意:

    フィーチャ サービスを使用して編集するには、LRS ネットワークがリニア リファレンスおよびバージョン管理機能を備えた状態で公開される必要があります。

  8. Click the Effective Date drop-down arrow and choose a date for the edit.
    ヒント:
    • Optionally, type the date in the Effective Date text box.
    • Double-click the empty Effective Date text box to populate it with today's date.
  9. If the centerline touches the routes, the From Route Name, From Measure, To Route Name, and To Measure parameters in the Source Route section are autopopulated.

    If the centerline doesn't touch the route, you can use the pickers to populate the From Route Name, To Route Name, From Measure, and To Measure parameters. Additionally, you can type the measure values.

  10. The From Measure value in the Realigned Route section is automatically populated.

    The suggested from measure value is the measure at the location where the start of the centerline touches the source route.

    • Optionally, you can type a from measure value of your choice.
    • If you do not know the from measure, allow Roads and Highways to suggest it. Click the Recalculate From Measure button 開始メジャー値の再計算 to do so. This value is calculated as the difference between the to measure value and the geometric length of the centerline.
  11. The to measure value is automatically populated in the Realigned Route section.

    The suggested to measure value is the measure at the location where the end of the centerline touches the target route. It is calculated by the geometric length of the centerline minus the to measure.

    注意:
    • Optionally, you can type a to measure value of your choice.
    • If you do not know the to measure, allow Roads and Highways to suggest it. Click the Recalculate To Measure button 終了メジャー値の再計算 to do so. This value is calculated as the sum of the from measure value and the geometric length of the centerline.
  12. Click Run.
    注意:

    If your route edit will result in the introduction of one or more physical gaps on the route, a prompt appears to alert you before the tool is run. If you didn't plan to create a gapped route, answer No and edit your digitized centerlines so that no gaps result during route editing.

    You can prevent unplanned centerlines by enabling snapping in the active map, or by enabling snapping using the Edit tab, Snapping group, Snapping button スナップ別にリスト.

    You can disable this warning by unchecking Warn before allowing route edits that can create physical gaps in Location Referencing options.

    The route realignment goes through.

Realign routes in a line network

Route realignment in a line network is supported using the following rule: The centerlines used for realignment must not touch the route being realigned.

The following examples illustrate this rule.

In the first example below, the centerline touches route R1, so only route R2 can be realigned.

Example 1: Before realignment

Route IDLine Order

R1

100

R2

200

Example 1: Before realignment

The line orders are updated as per the new realignment.

Example 1: After realignment

Route IDLine Order

R1

200

R2

100

Example 1: After realignment

In this second example, the centerline touches route R2, so only route R1 can be realigned.

Example 2: before realignment

Route IDLine Order

R1

100

R2

200

Example 2: Before realignment

Example 2: After realignment

Route IDLine Order

R1

100

R2

200

Example 2: After realignment

The line orders are updated as per the new realignment.

Use the following steps to realign routes in a line network:

  1. 中心線フィーチャクラスとネットワーク フィーチャクラスをマップに追加します。

    中心線フィーチャクラスとネットワーク フィーチャクラスがすでに存在するマップを開くこともできます。

    注意:

    情報モデルでは、特定場所で 1 つの中心線のみが必要です。 編集に使用している中心線が LRS で他の中心線と重なり合っていないことを確認します。

    注意:

    トラディショナル バージョン対応ネットワークは、ジオデータベースへの直接接続を介して編集する必要があります。 ブランチ バージョン対応ネットワーク (ユーザー生成ルート ID を使用して構成されたネットワークを含む) は、フィーチャ サービスを通じて編集する必要があります。

  2. Zoom in to the location where you want to realign the route.

    注意:

    The centerline feature for realigning the route must exist in the centerline feature class before realigning the route.

  3. On the Location Referencing tab, in the Routes group, click Realign 再配置.
    Realign button

    The Realign Route pane appears with the Select By Rectangle option 四角形による選択 as the default.

  4. Use your mouse to select one or more centerlines by rectangle at the location of the new route.

    You can also click the Select one or more centerlines drop-down arrow to choose one of the remaining selection tools: Select By Polygon Select by Polygon, Select By Lasso Select by Lasso, Select By Circle Select by Circle, Select By Line Select by Line, or Select By Trace トレースによる選択.

    Alternatively, you can use the interactive selection tools on the Map tab on the ArcGIS Pro ribbon:

    The selected centerlines are highlighted on the map and the Allow choosing of one or more centerlines button 1 つ以上の中心線の選択を許可 appears in the Realign Route pane. The Selected Centerlines count is shown above the table.

  5. Click the Allow choosing of one or more centerlines button 1 つ以上の中心線の選択を許可.

    A table appears in the Realign Route pane with each chosen centerline in a numbered row that corresponds to the selection order. Chosen centerlines are numbered on the map and highlighted in dark blue. The sum of Chosen Centerlines is shown below the table.

    Realign Route pane
  6. Optionally, change the centerline selection order by choosing one or more rows from the Order column and using the buttons below the table. You can also drag rows into the desired order.

    Changes in the table selection order are also shown on the map.

    Tools available in the centerlines table

    ToolTool nameTool description
    1 つ以上の中心線の選択を許可

    Allow choosing one or more centerlines

    Allows you to choose the centerlines on the map and displays them in a table by order of selection. Use the move buttons below the table or drag rows to reorder the chosen centerlines.

    現在選択されている中心線を消去

    Clear the currently chosen centerlines

    Clears the chosen centerlines and keeps the selected centerlines. You can reselect after clicking this button or click the Allow choosing one or more centerlines button a second time.

    選択した中心線を上に移動

    Move chosen centerlines up

    Moves one or more selected centerlines up a row in the table order.

    選択した中心線を最上位へ移動

    Move chosen centerlines to the top

    Moves one or more centerlines to the top of the table order.

    選択した中心線を下に移動

    Move chosen centerlines down

    Moves one or more centerlines down a row in the table order.

    選択した中心線を最下位へ移動

    Move chosen centerlines to the bottom

    Moves one or more centerlines to the bottom of the table order.

    中心線の方向を反転

    Flip the direction of the centerlines

    Reverses the direction of the chosen centerlines.

    選択した中心線を削除

    Remove the chosen centerlines

    Removes the chosen centerline from the table order but leaves it selected.

    ヒント:

    To change the display field shown in the centerlines table, right-click the centerline feature class in the Contents pane and choose Properties from the context menu. On the Layer Properties dialog box, click the Display tab, and click the Display field drop-down arrow to change its value. In the previous image, the display field is OBJECTID.

  7. In the Realign Route pane, choose the network in which the realignment will take place.
    注意:

    フィーチャ サービスを使用して編集するには、LRS ネットワークがリニア リファレンスおよびバージョン管理機能を備えた状態で公開される必要があります。

  8. Click the Effective Date drop-down arrow and choose a date for the edit.
    ヒント:
    • Optionally, type the date in the Effective Date text box.
    • Double-click the empty Effective Date text box to populate it with today's date.
  9. Depending whether the centerline touches the route, do one of the following:
    • If the centerline touches the route, the From Route IDFrom Measure and To Measure parameters in the Source Route section are autopopulated.
    • If the centerline doesn't touch the route, you can use the pickers to populate the From Route NameFrom Measure and To Measure parameters. Additionally, you can type the measure values.
  10. In the Realigned Route section, populate the route ID by doing one of the following:
    1. Click the Choose route from map button マップからルートを選択 and click an existing route on the same line. The route should not be the one that the centerline touches.
    2. Type the route ID of an existing route on the same line. The route should not be the one that the centerline touches.

      If the typed route ID is not present in the data, then a new route (with the typed RouteID) gets created on the same line.

  11. The From Measure value in the Realigned Route section is automatically populated.

    The suggested from measure value is the measure at the location where the start of the centerline touches the source route. To change the suggested from measure, do one of the following:

    注意:

    The From Measure and To Measure are not suggested if the centerline is not coincident on the source routes.

    To change the suggested from measure, do one of the following:

    • Type a From Measure value of your choice.
    • If you do not know the from measure, allow Roads and Highways to suggest it. Click the Recalculate From Measure button 開始メジャー値の再計算.
  12. The To Measure value in the Realigned Route section is automatically populated.

    The suggested To Measure value is the measure at the location where the end of the centerline touches the target route. It is calculated by the geometric length of the centerline plus the to measure.

    To change the suggested from measure, do one of the following:

    • Type a To Measure value of your choice.
    • If you do not know the from measure, allow Roads and Highways to suggest it. Click the Recalculate To Measure button 終了メジャー値の再計算.
  13. Click Next.

    The tool transitions to the next page, in the routes that are going to be retired due to the realignment are listed.

    Realign Route pane, list of routes to retire
  14. Click Run.
    注意:

    If your route edit will result in the introduction of one or more physical gaps on the route, a prompt appears to alert you before the tool is run. If you didn't plan to create a gapped route, answer No and edit your digitized centerlines so that no gaps result during route editing.

    You can prevent unplanned centerlines by enabling snapping in the active map, or by enabling snapping using the Edit tab, Snapping group, Snapping button スナップ別にリスト.

    You can disable this warning by unchecking Warn before allowing route edits that can create physical gaps in Location Referencing options.

    The route realignment is completed.